ADS-SHR-DOC-SPECTECH
  • UiTM/B1/PER/SHR/B/0525/0021
  • Cadangan Membekal, Menghantar, Memasang, Mengujilari Dan Menyelenggara Peralatan Pengajaran dan Pembelajaran Untuk Makmal Komunikasi 2 (Semikonduktor 04), Fakulti Kejuruteraan Elektrik, UiTM Shah Alam, Selangor.
  • Electrical/Electricity/Electronic Wares : Relay Control Board/ Relay Module
  • Analog Communication Trainers
  • 9 Set

Maklumat Spesifikasi Teknikal

  
Keterangan Calit Tawaran/Catatan
1. GENERAL REQUIREMENTS -
I. Vendors must comply with all the requirements specified in this tender document
Ya

Tidak
II. Vendors must bear all costs of supplying the specified quantity of items to UiTM. Such costs shall include the costs of delivery, installation, commissioning, training, troubleshoot and maintenance work (including parts labour and on-site service) within the specified warranty period
Ya

Tidak
2. SPECIFICATION -
I. The trainer includes the basic & advanced modules to experiment on fundamental & higher
level of analog & digital topics of a telecommunication course. The purpose of the modules is to enable
the student to acquire a clear experimental view of the basic & advanced concepts and familiarization
with the operative aspects of the work in the telecommunication laboratory. This trainer combined the
modules with experimental circuits. It can offer the beginner complete courses of basic & advanced
communication in 10 Analog Experiments Modules, then they can complete various experiments independently.
Ya

Tidak
II. List Of Experiments:
-
A ) Second Order Active Filters & RF Oscillators Experiments Module
Second Order Active Filters
  • Experiment 1 Second Order Active Low-pass Filter (Low-pass -3dB Frequency: 1 kHz ~ 3 kHz)
  • Experiment 2 Second Order Active High-pass Filter (High-pass -3 dB Frequency: 5 kHz ~ 10 kHz)
  • Experiment 3 Second Order Active Band-pass Filter (Center Frequency:10 kHz ~ 100 kHz,Bandwidth: (6 kHz ~ 60 kHz)
  • Experiment 4Second Order Active Band-stop Filter (Cutoff Frequency: 10 kHz ~ 100 kHz,Bandwidth:6 kHz ~ 60 kHz)

RF Oscillators
  • Experiment 1 Colpitts Oscillator (Oscillation Frequency: 1 MHz ~ 9 MHz)
  • Experiment 2 Hartley Oscillator (Oscillation Frequency: 500 kHz ~ 1.8 MHz)
  • Experiment 3 Crystal Oscillator (Oscillation Frequency: 500 kHz ~ 1.8 MHz)
  • Experiment 4 Voltage Controlled Oscillator (Oscillation Frequency: 3.5 MHz ~ 4 MHz)
 Ya

Tidak
B ) AM Modulator
  • Experiment 1 Transistor AM Modulator (Carrier Signal: 1.5 kHz ~ 2 kHz, Audio Signal: 500 Hz ~ 1
  • kHz)
  • Experiment 2 MC1496 AM Modulator (Carrier Signal: 500 kHz ~ 1 MHz, Audio Signal: 500 Hz ~ 1
  • kHz)
 Ya

Tidak
C ) AM Demodulator
  • Experiment 1 AM Diode Detector (Carrier Signal:300 kHz, Audio Signal: 500 Hz ~ 2 kHz)
  • Experiment 2
  • AM Product Detector (Carrier Signal: 500 kHz ~ 1 MHz, Audio Signal: 500 Hz ~ 1
  • kHz)
 Ya

Tidak
D ) DSB-SC and SSB Modulator
  • Experiment 1 DSB-SC Modulator (Carrier Signal: 100 kHz ~ 500 kHz, Audio Signal: 500 Hz ~ 1
  • kHz)
  • Experiment 2 SSB Modulator (Carrier Signal: 200 kHz, Audio Signal: 500 Hz ~ 1 kHz)
 Ya

Tidak
E ) DSB-SC and SSB Demodulator
  • Experiment 1
  • DSB-SC Product Detector (Carrier Signal: 100 kHz ~ 500 kHz, Audio Signal: 500 Hz
  • ~ 1 kHz)
  • Experiment 2 SSB Product Detector (Carrier Signal: 200 kHz, Audio Signal: 500 Hz ~ 1 kHz)
 Ya

Tidak
F ) FM Modulator
  • Experiment 1 MC4046 FM Modulator (Carrier Signal: 20 kHz, Audio Signal: 1 kHz)
  • Experiment 2 LM566 FM Modulator (Carrier Signal: 20 kHz, Audio Signal: 500 Hz ~ 700 Hz)
 Ya

Tidak
G ) FM Demodulator
  • Experiment 1 MC4046 FM Demodulator (Carrier Signal: 20 kHz, Audio Signal: 1 kHz)
  • Experiment 2 LM565 FM Demodulator (Carrier Signal: 20 kHz, Audio Signal: 500 Hz ~ 700 Hz)
 Ya

Tidak
H ) TDM Multiplexer
  • Experiment 1 Waveform Generator (Sine Wave Signal Generator: 13 kHz, Triangle Wave SignalGenerator: 2.3 kHz, Square Wave Signal Generator: 2.3 kHz)
  • Experiment 2 TDM Multiplexer (Transmission Channels: 3 Channels, Switching Time:500 ms ~ 50ms)
 Ya

Tidak
I ) TDM Demultiplexer
  • Experiment 1
TDM Demultiplexer (Transmission Channels: 3 Channels, Switching Time:500 ms ~ 50 ms)
Ya

Tidak
J ) FDM Multiplexer
  • Experiment 1 FDM Signal Generator (Carrier Signal: 500 kHz ~ 1.5 MHz, Audio Signal: 500Hz~1.5kHz)
  • Experiment 2 DSB-SC Modulated Signal Generator (Carrier Signal: 500 kHz ~ 1.5 MHz, Audio Signal: 500 Hz ~ 1.5 kHz)
  • Experiment 3 FDM Multiplexer (Modulation Type: DSB-SC Signal, Transmission Bandwidth: 2 MHz)
 Ya

Tidak
K ) FDM Demultiplexer
  • Experiment 1 FDM Demultiplexer (Modulation Type: DSB-SC Signal, Demultiplexing Type: Product Demultiplexer)
 Ya

Tidak
L ) Analog-to-Digital Converter
  • Experiment 1 ADC0804 Analog-to-digital Converter (Resolution: 8 bits, Analog Input Voltage: 0 V ~ 5 V)
  • Experiment 2 ADC0809 Analog-to-digital Converter (Resolution: 8 bits, Analog Input Voltage: 0 V ~ 5 V)
 Ya

Tidak
M ) Digital-to-Analog Converter
  • Experiment 1 R-2R Digital-to-analog Converter (Digital Input: 4 bits, Analog Output: 0 V ~ 5 V)
 Ya

Tidak
N ) Frequency Converter
  • Experiment 1 Frequency Multiplier (Carrier Signal: 10 kHz)
  • Experiment 2 Up/Down Frequency Converter (Carrier Signal @ LO port: 100 kHz; Carrier Signal @ RF port: 120 kHz)
 Ya

Tidak
O ) Signal Recovery
  • Experiment 1 Carrier Signal Recovery Circuit (Carrier Signal: 10 kHz)
  • Experiment 2 Clock Recovery Circuit (Clock Signal: TTL, Encoded Signal: Manchester, Clock Frequency: 5 kHz ~ 10 kHz)
 Ya

Tidak
III. Accessory Sets:
  • 2mm Stackable Test Lead Set (350mm Length)
Assorting in 5 different colors 30 units : Red x 6, Yellow x 6, Blue x 6, Black x 6,
Green x 6
  • 4mm Stackable Test Lead Set (350mm Length)
Assorting in 5 different colors 10 units : Red x 2, Yellow x 2, Blue x 2, Black x 2,
Green x 2
  • Experiments Frame (1450mm Length)
a. Epoxy Coated Steel Bended T Slot Frame
b. Din Standard A4 With Two Shelves
c. Side Frame: T Shape
d. Dimension:
  • Length : 1450mm
  • Width : 20mm
  • Height : 300mm
 Ya

Tidak
IV. Universal Lab Station:
  • DC Power Supply
Fixed Output: +5V/0.5A, -5V/0.5A, +12V/0.5A, -12V/0.5A
Variable
Output: +0V ~ +23V/0.5A, -0V ~ -23V/0.5A
  • AC Power Supply
Fixed Output: 19V–15V–9V–0V–9V–15V-19V
  • Function Generator
Sine, Triangle and Square waveform output, Frequency range: 1Hz to 1MHz in 6 decades, With fine adjust, Amplitude and DC offset control, TTL Mode Output Range: 1Hz to 1MHz in 6 decades
Six frequency ranges:
1Hz to 10Hz, 10Hz to 100Hz, 100Hz to 1KHz, 1KHz to 10KHz, 10KHz to 100KHz, 100KHz to 1MHz
Sine wave output: 0 to 12V peak to peak variable, Triangle wave output: 0 to 8V peak to peak variable, Square wave output: 0 to 16V peak to peak variable
  • Five (5) Data Switches Module
5 units slide switches and corresponding output terminals. When switch is set at "down” position, the
output is LO level; contrarily, it is to be HI level when setting at "up” position.
  • Multi Interface Adaptor Module
Miniature Socket, 2mm Socket & 4mm Banana Adaptors
Ya

Tidak
3. CATALOGUES / BROCHURES -
I. Vendors must provide the catalogues / brochures / technical specification manuals with the tender proposal
Ya

Tidak
II. Original copies of user and operational manual of the equipment must be provided
Ya

Tidak
4. WARRANTY AND SUPPORT -
I. Vendors must have local service for repair services and provide on call services when required by UiTM
Ya

Tidak
II. Vendors must provide details of warranty. INCLUDING ALL parts, labour, basic phone support for hardware issue, repairs onsite). Please attach the Letter of Warranty (LOW) from the principle, which states that UiTM is entitled to three (1) years of warranty upon project completion
Ya

Tidak
III. Vendors be responsible for the installation, commissioning and test-run of the equipment and accompanying software (if applicable) to the satisfaction of UNIVERSITI TEKNOLOGI MARA before final acceptance.
Ya

Tidak
IV. All cost on delivery. installation, commissioning, training and test run shall be borne by the vendor
Ya

Tidak
V. The vendors MUST provide a genuine product. The vendors must be supported back-to-back by a principle (manufacturer) to provide maintenance services for equipment supplied. The vendors should attach a Letter of Authorization (LOA) from Distributors/ Principal.
Ya

Tidak
VI. Free support through fax, email, telephone must be provided during the warranty period
Ya

Tidak
5. OTHER REQUIREMENTS

 -
I. Note that all other related material, components, cabling and others, which are required to ensure full operation of the above package must be supplied and borne by vendors
Ya

Tidak
6. TRAINING -
I. Tenderers are required to provide training for the use, maintenance and troubleshoot of the equipment to the Technical Staff & Lecture of Electrical Engineering School, College of Engineering, UiTM Shah Alam and all training-related costs are borne by the tenderers.
Ya

Tidak
II. A minimum of two (2) days training for a minimum of five (5) participants covering each module. (Vendors must provide details/syllabus of the training module)
Ya

Tidak
III. Complete training materials and documentation must be provided to all participants
Ya

Tidak
IV. The training MUST be conducted by trainers who are certified by principal. Please attach the trainer's certification that is certified by principal supplier.
Ya

Tidak